Week 2: Inserting the Busk

So, today we’ll be seeing how to insert a Busk in to our Eventide Corsets! I love this bit of Corsetry, it’s when the Corset starts to look, well… like a Corset! It is also the first time we will be sewing with metal, which whilst not difficult, has it’s own set of rules.

The most important thing to remember is that your Sewing Machine is perfectly capable of sewing over the metal however; the Needle is not! I have clipped the edge of the Busk or Boning many times and the Needle not only breaks, it can fracture into small pieces which is not fun! It with damage the Fabric and invariable flies towards your face…

Firstly, you will need to select the Right hand Fabric and Coutil sections AS YOU WOULD WEAR THEM. To do this, lay the Fabric out, upside down as illustrated. With Right Sides Together, lay the Coutil on top then put the Left hand side to one side.

busk1 busk2

On the Coutil side, draw a line 3cm away from the edge. As you can see from the Pattern, this is the Centre Front Line. If you have a Patternmaster this will be super easy as you can line up the 3cm line and simply draw down as illustrated.

busk3 busk4 busk5

Place the Busk against this line, equidistant from the top and bottom, then draw either side of the Hooks. The two Hooks together go at the Bottom of the Busk, and the Busk should be laying as illustrated- with the Hooks against the Centre Front line.

 busk6 busk6a

After you have marked either side of the Hooks, Pin the layers together. On the Sewing Machine, sew in between the gaps (as shown below, far left with a pink dotted line) remembering to reverse stitch at the beginning and end of each little seam. Try not to stitch too far in to the gaps or the Busk Hooks will not fit through.

busk7 busk8 busk9

Don’t also forget that you can unpick at any moment if you are unhappy with the stitching.

Once happy, iron the Seam as follows… Iron the Seam out on the wrong side (below left), then wrap the Front around to the back so that on the Coutil side you can see a little of the Front fabric (below right) but none of the Coutil on the Right side.

busk10 busk11

Push the Busks Hooks through the holes, then push the Busk up against the Seam and hold firmly in place whilst pinning. The Busk needs to be hard up against the edge so that, when sewn, it is not baggy. A baggy Busk simply wont do!

Push the Pin in, then scrape the Pin along the back of the Coutil until you can feel the edge of the Busk, then pin through. Pinning like this will make sure the Pins hold the Busk in place nice and tightly.

busk12 busk13

When pinned, measure in from the edge of the Busk as as illustrated then, on the Sewing Machine, raise the Presser Foot and roll the Needle into the Machine. Place the measuring tape against the Needle, and use a Pencil to mark the Seam Allowance needed to stitch alongside the Busk.

Doing this makes sure that, above and below the Busk, you are able to sew in a neat line that is the same distance from the edge for the whole length. Marking with a Pencil means that you will be able to rub it off, alternatively you can use Washi Tape.

busk14 busk15

When you have you Seam Allowance marked, stitch along the side of the Busk from top to bottom. You will need to attach your Zipper Foot to do this. Because the Busk starts and finishes 5 or 6cm after the start or before the end your Seam Allowance mark will come in handy to guide you in a straight line to sew next to the Busk.

busk16 busk17

Voila! One beautifully inserted Busk!!

How easy was that? Join me tomorrow as I continue Corset Month with how to insert the Left side of the Busk.

Don’t forget, the Eventide Corset Pattern is available in a number of options including Instant Download here, and you can join in with Corset Month on FacebookTwitter (#corsetsessions) and Pinterest!

Happy stitching!

One thought on “Week 2: Inserting the Busk

  1. Pingback: Week 2: Inserting the Busk Pt II | Laura After Midnight

Leave a Reply

Your email address will not be published. Required fields are marked *